With a lineup starting from small diameter shafts, it can be used for shafts with a wide range of tolerances.

• ・Compatible with a wide range of shaft tolerances. Standard products are compatible with plus tolerance shafts of servo motors, etc.
• - The small inner/outer diameter ratio allows for compatibility with small hub diameter. Compact design is possible.
• - With a lineup starting from small diameter sizes, it is ideal for fastening small stepping motors and servo motor output shafts.
• - Simple structure with few parts, excellent cost performance.
• -In addition to stainless steel and electroless nickel plating specifications, we also offer Low Contact Pressure series.
• *Centering function included. No need for troublesome boss step processing.
• *The boss does not move during assembly.

This is the most popular global standard model.

• - This series is highly compatible and is available from many manufacturers both domestically and internationally.
• - By using high-strength bolts, fewer tightening bolts are required than other companies' products, reducing assembly time.
• - The large taper angle makes it easy to tighten and remove. It is the easiest to handle in the series.
• ・We cover a wide range of shaft diameters from Φ19 to Φ500. Inch sizes are also available.
• ・Stainless steel and electroless nickel plating specifications are also available. Choose according to your application.
• *It does not have a centering function, so a guide must be provided on the boss.
• *The boss does not move during assembly.

Large capacity torque transmission type.

• -It has a transmission torque capacity 1.5 to 3 times greater than the AS series.
• · It has the same inner and outer diameter as the AS series, making it easy to replace multiple AS series units.
• ・Electroless nickel plating specifications are also available. Ideal for transmitting large torque in clean rooms.
• ・Tsubaki is the only company that offers a lineup starting from Φ19. Leave the transmission of large torque on small diameter shafts to us.
• * Careful assembly and removal is required.
• *Centering function included. No need for troublesome boss step processing.
• *The boss does not move during assembly.

It has the same inner and outer diameter as the AS series, but comes with a flange and centering function.

• - It has the same inner and outer diameter as the AS series, and is suitable for cases where a centering guide section cannot be installed.
• - A simple type consisting of three parts: inner ring, outer ring, and tightening bolt.
• - This series is highly compatible and is available from many manufacturers both domestically and internationally.
• *Centering function included. No need for troublesome boss step processing.
• *The boss does not move during assembly.
• *When mounting on a stepped shaft, leave a gap of 1 mm or more between the boss and the stepped part.
  If there is no gap, it may be difficult to remove.

This series has the smallest inner and outer diameter ratio and is ideal for small hub diameter.

• - The smallest inner/outer diameter ratio in the series, so it can be used even when the boss diameter is small.
• - The number of tightening bolts is the smallest in the series, reducing assembly time.
• - This series is highly compatible and is available from many manufacturers both domestically and internationally.
• - Electroless nickel plating specifications are also available.
• - It consists of four parts: inner ring, outer ring, spacer, and tightening bolt.
• *Centering function included. No need for troublesome boss step processing.
• *The boss does not move during assembly.

This is the simplest element type and allows for optimal design.

• ・Bolt tightening and the number of Power-Lock ELs to be installed can be freely selected, allowing you to select the optimum tightening force depending on the required tightening force.
  Design is possible.
• The perfect ring shape provides excellent dynamic balance.
• - Compact and lightweight, it does not take up more space than necessary for installation.
• - It is inexpensive and suitable for large-scale use.
• - This series is highly compatible and is available from many manufacturers both domestically and internationally.
• *The pressure flange, pressure sleeve, and tightening bolts must be provided by the customer.
• *Outer ring pressure is the standard, in which case the boss does not move during assembly.
• *It does not have a centering function, so a guide must be provided on the boss.

It is a pressure flange integrated type with the same inner and outer diameter as the EL series.

• · It is an integrated pressure flange with the same inner and outer diameter as the EL series, eliminating the need to manufacture a pressure flange.
• -It has 2 to 3 times the transmission torque of the EL series, so it can be used as a replacement for multiple ELs.
• - The small inner/outer diameter ratio allows it to be used with small hub diameter.
• - A simple type consisting of three parts: inner ring, outer ring, and tightening bolt.
• ・This is a Tsubaki-exclusive series that is not available from other companies.
• *Centering function included. No need for troublesome boss step processing.
• *When assembling, the boss will move slightly forward in the axial direction. Please contact us for details.

A simple fastening type that can be easily fastened with just one nut.

• - Can be easily fastened with just one nut, significantly reducing assembly time.
• - The surface is plated for simple rust prevention, and the nuts also have a special surface treatment, so there is no need to apply oil during assembly.
• -The only one in the series that can be attached to bosses that are shorter than Power-Lock length.
• · The tightening torque can be changed within the range of 1/2 to 1.1 times the standard torque. It can be used to match the boss strength.
• *Shaft diameters up to Φ32 are ML type, and Φ34 and above are MG type, and the appearances are different.
• *Centering function included. No need for troublesome boss step processing.
• *When assembled, the boss will move slightly toward the rear in the axial direction. Please contact us for details.

This is an external tightening type that tightens from the outside of the boss.

• - Ideal for fastening hollow shafts such as reducers.
• -It can also be used when the boss thickness cannot be secured due to the design.
• - Special surface treatment has been applied, so there is no need to apply oil during assembly.
• - The thicker the shaft diameter, the greater the torque that can be transmitted.
• - Simple structure makes it easy to install and remove.
• *The boss does not move during assembly.
• *If used with a hollow shaft, the inner diameter of the hollow shaft must be considered when selecting.