sizing　Small size conveyor chain

We will select the appropriate Small size conveyor chain based on your specified conditions.

Provisional selection of chain type

Please select the chain specification.

type

Roller type

Specification 1

Specification 2

Specification 3

*If you are considering using stainless steel NS, stainless steel LSK, or KF Series,
Please contact the following inquiry desk.


Please enter or select the conditions of use below and press the provisional selection button.

・Please use “.” for the decimal point and not “,” as the calculation error will occur.

Parallel/ single strand

2 parallel

single strand

If you are using three or more in parallel, please contact us at the following inquiry desk.

Conveying speed V

m/min

(maximum 120)

Total mass of transported items W

kg

Select a guide method


Lubrication between rollers and bushings


PLEASE WAIT...

Velocity factor Kv
gravitational acceleration 9.80665
Friction coefficient f1
Maximum static tension kN
size
Maximum allowable load kN
Approximate Mass kg/m
Pitch mm

A tentative selection was made.
Please check the allowable loads for the rollers and attachments below.

Check the allowable load

No chains were found that meet the tension requirements you entered.

Check the allowable load

Roller allowable load

This value is with lubrication between the roller and bushing.

Size & Roller Type Roller
Allowable load kN
Roller allowable load

*RS25 and RS35 are bushed types and do not come with rollers. If you are considering using them, please contact us at the inquiry desk listed below.

Allowable load of attachment

A Attachment Allowable Load

Double pitch
size steel
kN		 Stainless steel
less
kN
RF2040 0.262 0.108
RF2050 0.455 0.189
RF2060 1.06 0.419
RF2080 1.67 0.646
RF2100 2.51 1.15
RF2120 3.68 1.79
RF2160 5.84 3.13
With attachment
RS type chain
size steel
kN		 Stainless steel
less
kN
RS25 0.028 0.012
RS35 0.094 0.036
RS40 0.13 0.054
RS50 0.243 0.101
RS60 0.376 0.148
RS80 0.591 0.233
RS100 0.933 0.361
RS120 1.39 0.629
RS140 1.82 0.869
RS160 2.36 1.19
Needle bushings and Bearing Cage Chain
size Foreign Pre
Gr kN		 Internal Pre
Gr kN
RF2040R 0.12 0.03
RF2050R 0.18 0.05
RF2060R 0.47 0.13
RF2080R 0.72 0.21

・The point of application of the vertical load that can be tolerated by one of the attachments A is the position of the attachment's mounting hole.

・K attachments are twice as powerful as A attachments.

- Please contact us for other types of attachments.

Allowable load of attachment

Proceed to the final selection

Make sure that the load on the rollers and attachments is below the values in the table above.
If this value is exceeded, change to a chain size that can tolerate the load and then proceed with the final selection.

Calculation of maximum tension (F) acting on the chain

Please select the transportation method.

Horizontal transport

Vertical Conveyance

Inclined conveyance

Horizontal and inclined transport

Please enter or select the conditions of use below and press the "Select" button.

type
Roller type
Specification 1
Specification 2
Specification 3
Conveying speed V
Total mass of transported items W
Guide Method
Lubrication between rollers and bushings
Velocity factor Kv
gravitational acceleration9.80665
Friction coefficient f1

スプロケット中心距離(水平方向) L

m

スプロケット中心距離(垂直方向) H

m

スプロケット中心距離(傾斜搬送) C

m

スプロケット中心距離2(水平･傾斜搬送) C2

m

Attachment Type

[figure]

[figure]

[figure]

[figure]

[figure]

[figure]

[figure]

[figure]

[figure]

[figure]

kg/piece

Attachment mounting interval

One per link

Jig mass per meter
Buckets, aprons, etc.

kg/m

PLEASE WAIT...

The selection has been completed. Please check the selection results below.

The provisionally selected model number does not have enough tension.
Change the provisionally selected chain size to a larger one and then perform the final selection.

Selection results

Parallel/ single strand Acting tension kN
(per bottle)		 Product name allowable tension kN Tension margin Roller
Allowable load kN		 Required power kW

*RS25 and RS35 are bushed types and do not come with rollers. If you are considering using them, please contact us at the inquiry desk listed below.

Make sure that the load on the rollers and attachments is below the allowable value.

Please note that this calculation result is an estimate and may not be usable depending on the operating temperature, environmental atmosphere, and other conditions.